Datasheets»Panasonic Corporation»AN12975A Datasheet

AN12975A Datasheet

Download or read online Panasonic Corporation AN12975A Stereo BTL Amplifier IC With Built-in AGC pdf datasheet.
Also see for AN12975A: Datasheet #2 (22 pages)



Page
1 of 22
next
DATA SHEET
AN12975A
Part No.
Package Code No.
ULGA020-L-0404
Publication date: February 2008
SDE00029AEB
1

Summary of Contents

Page 1

... DATA SHEET Part No. Package Code No. Publication date: February 2008 AN12975A ULGA020-L-0404 SDE00029AEB 1 ...

Page 2

... AN12975A Overview ... 3 Features … ...

Page 3

... AN12975A Overview AN12975A is the stereo BTL amplifier which contained the AGC circuit for clip prevention of a speaker output. This IC performs a mode change by the I Features 2 Selection bus control is possible in the on-level of AGC. 2 Selection bus control is possible in an attack/recovery time of AGC. ...

Page 4

... AN12975A Application Circuit Example (Block Diagram) PREOUT-R 16 100 pF 10 kΩ 0.1 μF 17 IN(R) FB-R 10 kΩ GND 18 0.1 μF 10 kΩ FB-L 19 IN(L) 10 kΩ 100 pF 20 PREOUT-L Note) This circuit and these circuit constants show an example and do not guarantee the design as a mass-production set. VCC μF 1 μ ...

Page 5

... AN12975A Pin Descriptions Pin No. Pin name 1 TEST2 2 SCL 3 SAD Input / Output 4 VCC_D Power Supply 5 LOUT_POS 6 GND_SPL 7 LOUT_NEG 8 VCC_SP Power Supply 9 ROUT_NEG 10 GND_SPR 11 ROUT_POS 12 VREF_SP 13 TEST1 14 VCC Power Supply 15 VREF 16 PREOUT_R 17 FB_R 18 GND 19 FB_L 20 PREOUT_L Type Terminal for testing (please connect to Ground) ...

Page 6

... AN12975A Absolute Maximum Ratings A No. Parameter 1 Supply voltage 2 Supply current 3 Power dissipation 4 Operating ambient temperature 5 Storage temperature Note) 1: The values under the condition not exceeding the above absolute maximum ratings and the power dissipation. 2: The power dissipation shown is the value at T When using this IC, refer to the P ...

Page 7

... AN12975A Electrical Characteristics at VCC 3 VCC_D 1 VCC_SP 3.0 V Note 25°C±2°C unless otherwise specified Parameter No. Circuit Current Circuit current 1A at non-signal 1 (VCC) Circuit current 2A at non-signal 2 (VCC_SP) Circuit current 3A at non-signal 3 (VCC_D) Circuit current 1B at non-signal 4 (VCC) Circuit current 2B at non-signal ...

Page 8

... AN12975A Electrical Characteristics at VCC 3 VCC_D 1 VCC_SP 3.0 V (continued) Note 25°C±2°C unless otherwise specified Parameter No interface 43 SCL, SDA signal input low level 44 SCL, SDA signal input low level SDA output signal low level 45 46 SCL, SDA signal input current ...

Page 9

... AN12975A Electrical Characteristics (Reference values for design) at VCC 3 VCC_D 1.8 V, VCC_SP 3 25°C±2°C unless otherwise specified. a The characteristics listed below are reference values derived from the design of the IC and are not guaranteed by inspection problem does occur related to these characteristics, we will respond in good faith to user concerns. ...

Page 10

... AN12975A Technical Data I 2 C-bus Mode 1. Write Mode SAD SCL SLAVE ADDRESS START CONDITION Two transmission messages (i.e., the SCL and SDA) are sent in synchronous serial transmission. The SCL is a clock with fixed frequency. The SDA indicates address data for the control of the reception side, and is sent in parallel in synchronization with the SCL. ...

Page 11

... AN12975A Technical Data (continued C-bus Mode (continued) 1. Write Mode (continued) ( C-bus PROTOCOL Slave address: 10110110 (B6Hex) Format (normal) S Slave address Start condition (b) Auto increment Sub-address 0Hex: Auto increment mode (When the data is sent in sequence, the sub address will change one by one and the data will be input.) ...

Page 12

... AN12975A Technical Data (continued C-bus Mode (continued) 1. Write Mode (continued) (e) AGC-attack-time selection Write Attack 01Hex Register time 0 (g) AGC-on-level selection (at VCC 3.0 V, VCC_SP 3.0V) Write 01Hex Register Note recommend more than VCC 2.9 V for 7 dBV output level. ...

Page 13

... AN12975A Technical Data (continued C-bus Mode (continued) 2. Read Mode (a)I 2 C-bus PROTOCOL Slave address 10110111(B7Hex) Format S Slave address Note) At the slave address input sequentially output from data 0. There is no necessity for inputting the sub-address. (b) Sub-address Byte and Data Byte Format ...

Page 14

... AN12975A Technical Data (continued) I/O block circuit diagrams and pin function descriptions Note) The characteristics listed below are reference values based on the IC design and are not guaranteed. Pin Waveform No. and voltage Test2 1 Hi-Z SCL 2 Hi-Z SAD 3 Hi-Z VCC_D 4 1.8 V(typ.) Internal circuit VCC 1k 1k VCC_D VCC_D GND - ...

Page 15

... AN12975A Technical Data (continued) I/O block circuit diagrams and pin function descriptions (continued) Note) The characteristics listed below are reference values based on the IC design and are not guaranteed. Pin Waveform No. and voltage LOUT_POS GND_SPL LOUT_NEG 7 DC 1.45 V VCC_SP 8 3.0 V(typ.) Internal circuit ...

Page 16

... AN12975A Technical Data (continued) I/O block circuit diagrams and pin function descriptions (continued) Note) The characteristics listed below are reference values based on the IC design and are not guaranteed. Pin Waveform No. and voltage ROUT_NEG GND_SPR ROUT_POS 11 DC 1.45 V VREF_SP 12 DC 1.45 V Internal circuit ...

Page 17

... AN12975A Technical Data (continued) I/O block circuit diagrams and pin function descriptions (continued) Note) The characteristics listed below are reference values based on the IC design and are not guaranteed. Pin Waveform No. and voltage Test1 13 Hi-Z VCC 14 3.0 V(typ.) VREF 15 DC 1.45 V PREOUT_R 16 DC 1.45 V Internal circuit ...

Page 18

... AN12975A Technical Data (continued) I/O block circuit diagrams and pin function descriptions (continued) Note) The characteristics listed below are reference values based on the IC design and are not guaranteed. Pin Waveform No. and voltage FB_R GND FB_L 19 DC 1.45 V PREOUT_L 20 DC 1.45 V Internal circuit 10k - ...

Page 19

... AN12975A Technical Data (continued) Power supply and logic sequence Note) The characteristics listed below are reference values based on the IC design and are not guaranteed. The timing control of power-ON/OFF and each logic according to the procedure below should be recommended for the best pop performance caused in switching ...

Page 20

... AN12975A Technical Data (continued) ⎯ diagram D a SDE00029AEB 20 ...

Page 21

... AN12975A Usage Notes output pin (Pin5, Pin7, Pin9, Pin11) power supply pin short, SP output pin (Pin5, Pin7, Pin9, Pin11) GND short output (Pin5, Pin7, Pin9, Pin11)-to-SP output-pin short (load short). It damaged when the electricity is turned on. SDE00029AEB 21 ...

Page 22

Request for your special attention and precautions in using the technical information and (1) If any of the products or technical information described in this book exported or provided to non-residents, the laws and regulations of the ...

Comments to this Datasheet