Datasheets»Microchip Technology»PIC16F87XATI/SP Datasheet

PIC16F87XATI/SP Datasheet - Page 179

Download or read online Microchip Technology PIC16F87XATI/SP 28/40/44-Pin Enhanced Flash Microcontrollers pdf datasheet.



Page
179 of 234
prevnext
17.2
DC Characteristics: PIC16F873A/874A/876A/877A (Industrial, Extended)
PIC16LF873A/874A/876A/877A (Industrial) (Continued)
DC CHARACTERISTICS
Param
Sym
Characteristic
No.
V
Output Low Voltage
OL
D080
I/O ports
D083
OSC2/CLKO (RC osc config)
V
Output High Voltage
OH
(3)
D090
I/O ports
D092
OSC2/CLKO (RC osc config)
D150*
V
Open-Drain High Voltage
OD
Capacitive Loading Specs on
Output Pins
D100
C
2 OSC2 pin
OSC
D101
C
All I/O pins and OSC2 (RC mode)
IO
2
D102
C
SCL, SDA (I
C mode)
B
Data EEPROM Memory
D120
E
Endurance
D
D121
V
V
for read/write
DRW
DD
D122
T
Erase/write cycle time
DEW
Program Flash Memory
D130
E
Endurance
P
D131
V
V
for read
PR
DD
D132A
V
for erase/write
DD
D133
T
Erase/Write cycle time
PEW
*
These parameters are characterized but not tested.
† Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance
only and are not tested.
Note 1:
In RC oscillator configuration, the OSC1/CLKI pin is a Schmitt Trigger input. It is not recommended that the
PIC16F87XA be driven with external clock in RC mode.
2:
The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels
represent normal operating conditions. Higher leakage current may be measured at different input voltages.
3:
Negative current is defined as current sourced by the pin.
 2001-2013 Microchip Technology Inc.
PIC16F87XA
Standard Operating Conditions (unless otherwise stated)
-40°C  T
 +85°C for industrial
Operating temperature
A
-40°C  T
 +125°C for extended
A
Operating voltage V
range as described in DC specification
DD
(Section 17.1)
Min
Typ†
Max
Units
0.6
V
I
= 8.5 mA, V
OL
-40C to +85C
0.6
V
I
= 1.6 mA, V
OL
-40C to +85C
V
– 0.7
V
I
= -3.0 mA, V
DD
OH
-40C to +85C
V
– 0.7
V
I
= -1.3 mA, V
DD
OH
-40C to +85C
8.5
V
RA4 pin
15
pF
In XT, HS and LP modes when
external clock is used to drive
OSC1
50
pF
400
pF
100K
1M
E/W -40C to +85C
V
5.5
V
Using EECON to read/write,
MIN
V
MIN
4
8
ms
10K
100K
E/W -40C to +85C
V
5.5
V
V
MIN
MIN
V
5.5
V
Using EECON to read/write,
MIN
V
MIN
4
8
ms
Conditions
= 4.5V,
DD
= 4.5V,
DD
= 4.5V,
DD
= 4.5V,
DD
= min. operating voltage
= min. operating voltage
= min. operating voltage
DS39582C-page 179

Comments to this Datasheet