Datasheets»Microchip Technology»PIC16LF1507 Datasheet

PIC16LF1507 Datasheet - Page 163

Download or read online Microchip Technology PIC16LF1507 20-Pin Flash, 8-Bit Microcontrollers pdf datasheet.



Page
163 of 266
prevnext
PIC16(L)F1507
20.1.2
DATA GATING
Outputs from the input multiplexers are directed to the
desired logic function input through the data gating
stage. Each data gate can direct any combination of the
four selected inputs.
Note:
Data gating is undefined at power-up.
The gate stage is more than just signal direction. The
gate can be configured to direct each input signal as
inverted or non-inverted data. Directed signals are
ANDed together in each gate. The output of each gate
can be inverted before going on to the logic function
stage.
The
gating
is
in
essence
a
AND/NAND/OR/NOR gate. When every input is
inverted and the output is inverted, the gate is an OR of
all enabled data inputs. When the inputs and output are
not inverted, the gate is an AND or all enabled inputs.
Table 20-2
summarizes the basic logic that can be
obtained in gate 1 by using the gate logic select bits.
The table shows the logic of four input variables, but
each gate can be configured to use less than four. If
no inputs are selected, the output will be zero or one,
depending on the gate output polarity bit.
TABLE 20-2:
DATA GATING LOGIC
CLCxGLS0
LCxG1POL
Gate Logic
0x55
1
0x55
0
0xAA
1
0xAA
0
0x00
0
0x00
1
It is possible (but not recommended) to select both the
true and negated values of an input. When this is done,
the gate output is zero, regardless of the other inputs,
but may emit logic glitches (transient-induced pulses).
If the output of the channel must be zero or one, the
recommended method is to set all gate bits to zero and
use the gate polarity bit to set the desired level.
Data gating is configured with the logic gate select reg-
isters as follows:
• Gate 1: CLCxGLS0
(Register
20-5)
• Gate 2: CLCxGLS1
(Register
20-6)
• Gate 3: CLCxGLS2
(Register
20-7)
• Gate 4: CLCxGLS3
(Register
20-8)
Register number suffixes are different than the gate
numbers because other variations of this module have
multiple gate selections in the same register.
DS41586A-page 163
Data gating is indicated in the right side of
Only one gate is shown in detail. The remaining three
gates are configured identically with the exception that
the data enables correspond to the enables for that
gate.
20.1.3
LOGIC FUNCTION
There are 8 available logic functions including:
• AND-OR
• OR-XOR
• AND
• S-R Latch
• D Flip-Flop with Set and Reset
1-to-4
input
• D Flip-Flop with Reset
• J-K Flip-Flop with Reset
• Transparent Latch with Set and Reset
Logic functions are shown in
function has four inputs and one output. The four inputs
are the four data gate outputs of the previous stage.
The output is fed to the inversion stage and from there
to other peripherals, an output pin, and back to the
CLCx itself.
20.1.4
OUTPUT POLARITY
The last stage in the configurable logic cell is the output
polarity. Setting the LCxPOL bit of the CLCxCON reg-
ister inverts the output signal from the logic stage.
Changing the polarity while the interrupts are enabled
AND
will cause an interrupt for the resulting output transition.
NAND
NOR
OR
Logic 0
Logic 1
Preliminary
Figure
20-2.
Figure
20-3. Each logic
 2011 Microchip Technology Inc.

Comments to this Datasheet